Todos os testes internacionais da IG MARITIME são gratuitos para marítimos. Basta registar-se uma vez para guardar o seu progresso e preparar-se sem limites.

EO1-Use Hand and Power Tools for Fabrication and Repair

Pesquisar nesta secção

Escolha um conjunto de perguntas e comece a estudar ou faça um exame de treino.

Sobre este conjunto

Na secção Видеотел encontra perguntas para estudo autónomo. Escolha um conjunto para estudar ou fazer um exame de treino.

«Видеотел — Engine Category — EO1-Use Hand and Power Tools for Fabrication and Repair» contém 172 perguntas em 1 conjunto.

Estudo

O modo de estudo não tem limite de tempo. Depois de responder, pode ver a avaliação e as opções corretas. Pode voltar a uma pergunta e repetir um tema.

Exame de treino

Um exame de treino dura até 60 minutos e inclui até 50 perguntas do conjunto selecionado. As soluções e os resultados aparecem no fim.

Exemplos de perguntas e respostas

Estes exemplos fazem parte do conjunto. Escolha Estudo para praticar pergunta a pergunta ou Exame de treino para testar os seus conhecimentos.

What kind of tool is shown bottom left ? What is its use ?Ilustração da pergunta

Uma resposta correta

  • 1) Mason's chisel / To break up cement boxes.
  • 2) Blacksmith's chisel / To cut steel bars and rods.
  • 3) Hot chisel / To cut bolts and nuts.
  • 4) Cold chisel / A general purpose cutting and splitting tool.✓ Resposta correta
A scriber should not be used for marking out?Ilustração da pergunta

Uma resposta correta

  • 1) When material is copper.
  • 2) When material is to be bent.✓ Resposta correta
  • 3) When material is to be hot worked.
  • 4) When material is plastic.
Perspex is an example of a thermoplastic, How is this best heated prior to bending?A imagem original não está disponível.

Uma resposta correta

  • 1) Heat in an oven.
  • 2) Heat in boiling water.✓ Resposta correta
  • 3) Flame heat.
  • 4) Hot air stream.
What is the function of this hydraulic stressing tool when fastening and unfastening bolts/nuts on an engine ?Ilustração da pergunta

Uma resposta correta

  • 1) To fasten or unfasten the nut.
  • 2) To press the part to be fastened together or down so that the nut can be tightened by hand.
  • 3) To apply pressure on cylinder head or bearing so that the bolts/nuts can be tightened by hand.
  • 4) To elongate the bolts at required stress value so that the nuts can be tightened to the position to ensure correct pre-tensioning.✓ Resposta correta
A method of joining two plastics together is by solvent welding. What is this process?A imagem original não está disponível.

Uma resposta correta

  • 1) Application of a thin film of adhesive to joining surfaces.
  • 2) Adhesive is applied and dissolves the plastic material being joined.✓ Resposta correta
  • 3) A heating tool is applied with pressure to required join.
  • 4) A high frequency current is applied to clamps at the join.

Antes de começar

Preciso de me registar para começar?

Pode aceder como visitante durante 23 minutos. Registe-se gratuitamente para continuar, guardar o progresso e rever os erros.

Em que idioma estão as perguntas?

As perguntas e opções mantêm o idioma original. Pode alterar separadamente o idioma da interface.

Posso usar o resultado como documento oficial?

Não. É uma prática autónoma. O resultado não substitui um exame, certificado ou avaliação de uma entidade autorizada.