Svi međunarodni probni testovi na platformi IG MARITIME besplatni su za pomorce. Registrirajte se jednom da biste spremili napredak i vježbali bez ograničenja.

CD0016. Corrosion Protection II

Pretraži ovaj odjeljak

Odaberite skup pitanja i započnite učenje ili probni ispit.

O ovom skupu

U odjeljku Seagull CBT dostupna su pitanja za samostalnu pripremu. Odaberite skup pitanja za učenje ili probni ispit.

„Seagull CBT — CD0016. Corrosion Protection II” sadrži 26 pitanja u 1 skupova.

Učenje

Učenje nema vremenskog ograničenja. Nakon odgovora dobit ćete povratnu informaciju i točne opcije. Možete ponoviti pitanje ili temu.

Probni ispit

Probni ispit traje do 60 minuta i uključuje do 50 pitanja iz odabranog skupa. Rješenja i rezultati prikazuju se nakon završetka.

Primjeri pitanja i odgovora

Primjeri su iz objavljenog skupa. Odaberite učenje za vježbu redom ili probni ispit za provjeru znanja.

The wet film of paint, which is applied, bears a direct relationship to the final dry film thickness of the coating. Taking wet film measurements can be very important. Why is it important to take these measurements as quickly as possible?

Jedan točan odgovor

  • To avoid the fresh coat softening the coats underneath leading to possible wrong readings.
  • So that the painter is disturbed as little as possible.
  • To obtain as close a reading to the actual wet film as possible.✓ Točan odgovor
Which of the following statements best describes one of the main advantages of Hydroblasting with fresh water as opposed to Dry Abrasive Blasting?

Jedan točan odgovor

  • Produces a Surface Profile to aid adhesion of coatings to the surface.
  • Only requires air power for operation.
  • As well as removing corrosion products it also removes salt contamination.✓ Točan odgovor
  • The prepared surfaces will flash rust.
A large area of exposed deck is to be blasted to an agreed standard of SA2 before application of an epoxy paint system. In the vicinity of some pipes where difficult access means that the blasting is not able to remove all the corrosion. What do you do?

Jedan točan odgovor

  • Reject the whole blasted areas until blasting is redone to the correct SA2 standard.
  • Accept the blasted areas and go ahead with painting.
  • Discuss the various options with the contractor.✓ Točan odgovor
Which are the 3 factors, which help contribute to correct performance of a paint system.

Više točnih odgovora

  • The Paint itself✓ Točan odgovor
  • The Correct Specification
  • The Correct Intervals between coats of paint
  • That clean Airless spray equipment is used
  • Proper Surface Preparation✓ Točan odgovor
  • The amount of Time and Money spent on the paint and the application
  • Proper Application of Paint✓ Točan odgovor
A large area of exposed deck is to be blasted to an agreed standard of SA2 before application of an epoxy paint system. In the vicinity of some pipes where difficult access means that the blasting is not able to remove all the corrosion. What do you do?

Jedan točan odgovor

  • Reject the whole blasted areas until blasting is redone to the correct SA2 standard.
  • Accept the blasted areas and go ahead with painting.
  • Discuss the various options with the contractor.✓ Točan odgovor

Prije početka

Trebam li se registrirati prije početka?

Pristup za goste traje 23 minuta. Besplatno se registrirajte za nastavak, spremanje napretka i pregled pogrešaka.

Na kojem su jeziku pitanja?

Pitanja i ponuđeni odgovori ostaju na izvornom jeziku. Jezik sučelja možete promijeniti zasebno.

Mogu li koristiti rezultat kao službeni dokument?

Ne. Ovo je samostalna vježba. Rezultat ne zamjenjuje ispit, potvrdu ni provjeru znanja ovlaštene ustanove.