Svi međunarodni probni testovi na platformi IG MARITIME besplatni su za pomorce. Registrirajte se jednom da biste spremili napredak i vježbali bez ograničenja.

CD0007. Inert Gas Generator

Pretraži ovaj odjeljak

Odaberite skup pitanja i započnite učenje ili probni ispit.

O ovom skupu

U odjeljku Seagull CBT dostupna su pitanja za samostalnu pripremu. Odaberite skup pitanja za učenje ili probni ispit.

„Seagull CBT — CD0007. Inert Gas Generator” sadrži 75 pitanja u 1 skupova.

Učenje

Učenje nema vremenskog ograničenja. Nakon odgovora dobit ćete povratnu informaciju i točne opcije. Možete ponoviti pitanje ili temu.

Probni ispit

Probni ispit traje do 60 minuta i uključuje do 50 pitanja iz odabranog skupa. Rješenja i rezultati prikazuju se nakon završetka.

Primjeri pitanja i odgovora

Primjeri su iz objavljenog skupa. Odaberite učenje za vježbu redom ili probni ispit za provjeru znanja.

What is the SOLAS requirement regarding non-return devices in the inert gas main for inert gas systems on oil tankers?

Jedan točan odgovor

  • There must be at least two devices one of which should be a water seal type.✓ Točan odgovor
  • There must be at least two water seal type devices fitted.
  • There must be at least two neither of which should be a water seal type.
  • As long as there is a water seal no other devices are required
When considering an independent, oil fired inert gas generator suitable for service onboard an oil tanker what are the SOLAS requirements for the oxygen content of the inert gas supply?

Jedan točan odgovor

  • A maximum of 5%.✓ Točan odgovor
  • A maximum of 8%.
  • A maximum of 11%.
  • A maximum of 3%.
When considering the automatic operation of an independent inert gas generator the start up sequence normally has delays built in to ensure correct timing of the sequence. For example there will be a delay in the sequence to ensure sufficient furnace purging time. How can these delays be ensured in manual mode?

Jedan točan odgovor

  • By the use of timed interlocks which operate even in the manual mode.✓ Točan odgovor
  • The operator is relied upon to ensure the correct timing of the sequence.
  • The delays are only an extra safety precaution so it doesn’t matter if they missed out.
  • There is no need for any delays if the operator is in attendance during start up.
When considering an independent, oil fired inert gas generator, other than providing a vent to the atmosphere during start up of the plant, what is the other main purpose of the automatic atmospheric vent valve?

Jedan točan odgovor

  • It is used in conjunction with the inert gas main valve to regulate the pressure in the inert gas main.✓ Točan odgovor
  • It acts as an inlet for fresh air to the system when gas freeing.
  • It acts as the main relief device in the event of overpressure.
  • It is used to control the capacity of the inert gas generator.
Which of the given options is the one that will most influence the combustion efficiency for the burner type described in this module?

Jedan točan odgovor

  • Distance from the main burner tip to the edge of the air cone.✓ Točan odgovor
  • Distance from main burner tip to pilot burner tip
  • Distance from pilot burner tip to igniter.
  • Distance from pilot burner tip to edge of air cone.

Prije početka

Trebam li se registrirati prije početka?

Pristup za goste traje 23 minuta. Besplatno se registrirajte za nastavak, spremanje napretka i pregled pogrešaka.

Na kojem su jeziku pitanja?

Pitanja i ponuđeni odgovori ostaju na izvornom jeziku. Jezik sučelja možete promijeniti zasebno.

Mogu li koristiti rezultat kao službeni dokument?

Ne. Ovo je samostalna vježba. Rezultat ne zamjenjuje ispit, potvrdu ni provjeru znanja ovlaštene ustanove.