Libre para sa lahat ng marino ang mga internasyonal na pagsasanay sa IG MARITIME. Magparehistro nang minsan para ma-save ang progreso at makapaghanda nang walang limitasyon.

CD7055. TOTS 1C-Operation, monitoring, machinery

Maghanap sa seksyong ito

Pumili ng pangkat ng mga tanong at magsimulang mag-aral o kumuha ng pagsusulit.

Tungkol sa pangkat na ito

May mga tanong sa Seagull CBT para sa sariling pag-aaral. Pumili ng pangkat para magsimulang mag-aral o kumuha ng pagsusulit.

May 76 tanong sa 1 pangkat ang “Seagull CBT — CD7055. TOTS 1C-Operation, monitoring, machinery”.

Pag-aaral

Walang timer sa pag-aaral. Makikita ang resulta at tamang sagot pagkatapos sumagot. Maaari mong balikan ang tanong at ulitin ang paksa.

Pagsusulit

Hanggang 60 minuto at 50 tanong mula sa napiling pangkat ang pagsusulit. Makikita ang mga tamang sagot at resulta kapag tapos na.

Mga halimbawang tanong at sagot

Galing sa pangkat na ito ang mga halimbawa. Piliin ang Pag-aaral para isa-isahin ang mga tanong, o Pagsusulit para suriin ang kaalaman mo.

If the safety valves fitted on an air reservoir can be isolated from the reservoir, then..

Isang tamang sagot

  • the reservoir must be fitted with a fusible plug.✓ Tamang sagot
  • the safety valve must be fitted with a fusible plug.
  • the compressor must be fitted with a fusible plug.
  • it can be used legally without any added safety measures.
What is the most common cause of the lowering in performance of heat exchangers?

Isang tamang sagot

  • Fouling of the heat transfer surface.✓ Tamang sagot
  • An air lock.
  • Low water flow.
  • The division plate joint failure.
During discharge, problems with the inert gas plant result in the production of clean inert gas being reduced by 50%. What do you do?

Isang tamang sagot

  • Advise the Chief Officer so that he can reduce the discharge rate in line with the reduction of the gas supply.✓ Tamang sagot
  • Adjust the boiler controls to increase the fuel and reduce the air in an attempt to reduce the oxygen content of the gas.
  • Allow the discharge to continue as the oxygen content in the tanks may not rise significantly during the remaining discharge period.
  • Shut down the discharge until the inert gas system problem is resolved.
In plate type coolers you would normally expect the plates to be made of..

Isang tamang sagot

  • titanium.✓ Tamang sagot
  • silver.
  • stainless steel.
  • nickel brass.
The cause of an abnormally high condenser pressure within a refrigeration system would be..

Isang tamang sagot

  • incondensable gases in the refrigerant.✓ Tamang sagot
  • a low cooling water flow through the condenser.
  • a defective thermal expansion valve.
  • an above normal level of refrigerant in the condenser.

Bago magsimula

Kailangan bang magparehistro bago magsimula?

May 23 minutong guest access. Magparehistro nang libre para magpatuloy, ma-save ang progreso at balikan ang mga pagkakamali.

Anong wika ang gamit sa mga tanong?

Nananatili ang orihinal na wika ng mga tanong at opsyon. Puwedeng baguhin nang hiwalay ang wika ng interface.

Maaari bang gamiting opisyal na dokumento ang resulta?

Hindi. Para sa sariling pagsasanay ito. Ang resulta ay hindi kapalit ng pagsusulit, sertipiko o pagtatasa ng awtorisadong organisasyon.