Libre para sa lahat ng marino ang mga internasyonal na pagsasanay sa IG MARITIME. Magparehistro nang minsan para ma-save ang progreso at makapaghanda nang walang limitasyon.

CD0420. Lockout Tagout

Maghanap sa seksyong ito

Pumili ng pangkat ng mga tanong at magsimulang mag-aral o kumuha ng pagsusulit.

Tungkol sa pangkat na ito

May mga tanong sa Seagull CBT para sa sariling pag-aaral. Pumili ng pangkat para magsimulang mag-aral o kumuha ng pagsusulit.

May 10 tanong sa 1 pangkat ang “Seagull CBT — CD0420. Lockout Tagout”.

Pag-aaral

Walang timer sa pag-aaral. Makikita ang resulta at tamang sagot pagkatapos sumagot. Maaari mong balikan ang tanong at ulitin ang paksa.

Pagsusulit

Hanggang 60 minuto at 50 tanong mula sa napiling pangkat ang pagsusulit. Makikita ang mga tamang sagot at resulta kapag tapos na.

Mga halimbawang tanong at sagot

Galing sa pangkat na ito ang mga halimbawa. Piliin ang Pag-aaral para isa-isahin ang mga tanong, o Pagsusulit para suriin ang kaalaman mo.

You are going to work on equipment that has been isolated, but which was previously pressurised or full of fluid. Which TWO of these precautions should be followed? Select the TWO best answers.

Maraming tamang sagot

  • Use any drain and vent valves fitted, checking that they are clear.✓ Tamang sagot
  • Loosen the bolts at off flanges but leaving the nuts on. Then just break the joint at the flange.✓ Tamang sagot
  • Give the isolating valves extra force with a wheel key.
  • Fully open a flange at the top of the equipment first.
How can safe isolation be maintained when more than one person is working on the same system, for instance in dry-dock? Select the ONE best answer.

Isang tamang sagot

  • Each person should apply their own locks at the points of isolation.✓ Tamang sagot
  • There should be a verbal agreement to check with each other before restoring the equipment to service.
  • One person should agree to take charge of the situation.
  • They should leave the locking arrangements to the Master or Chief Engineer.
If the equipment you are working on can move downwards under gravity, what should you do to keep safe? Select the ONE best answer.

Isang tamang sagot

  • Make sure that it is securely locked into position or properly supported.✓ Tamang sagot
  • Always work from above it.
  • Make sure that no-one can walk underneath it.
  • Only do the job when in port, so that the ship is not rolling.
If the person that applied the lock and tag out to a system is not available, what should be done when work is completed? Select the ONE best answer.

Isang tamang sagot

  • Follow the on board procedure for such an event.✓ Tamang sagot
  • The Chief Engineer or Chief Mate will remove them.
  • Anyone who has been involved in the work can remove them.
  • Leave them in place till the original person is available.
You have been working on electrical, pneumatic or hydraulic equipment. What should be done about the controls for the equipment before re-energising it? Select the ONE correct answer.

Isang tamang sagot

  • The controls should be put into a safe position, usually the ‘off’ position.✓ Tamang sagot
  • The controls should be checked to make sure they are in the same position they were when the work started.
  • Nothing needs to be checked, the equipment is not likely to start.
  • The controls should be placed to the ‘on’ position.

Bago magsimula

Kailangan bang magparehistro bago magsimula?

May 23 minutong guest access. Magparehistro nang libre para magpatuloy, ma-save ang progreso at balikan ang mga pagkakamali.

Anong wika ang gamit sa mga tanong?

Nananatili ang orihinal na wika ng mga tanong at opsyon. Puwedeng baguhin nang hiwalay ang wika ng interface.

Maaari bang gamiting opisyal na dokumento ang resulta?

Hindi. Para sa sariling pagsasanay ito. Ang resulta ay hindi kapalit ng pagsusulit, sertipiko o pagtatasa ng awtorisadong organisasyon.