Todas las pruebas internacionales de IG MARITIME son gratuitas para los marinos. Regístrate una vez para guardar tu progreso y prepararte sin límites.

CD0420. Lockout Tagout

Buscar en esta sección

Elige una colección de preguntas y empieza a estudiar o haz un simulacro de examen.

Sobre esta colección

La sección Seagull CBT ofrece preguntas para preparar la prueba por tu cuenta. Elige una colección para estudiar o hacer un simulacro de examen.

«Seagull CBT — CD0420. Lockout Tagout» contiene 10 preguntas en 1 colección.

Estudio

El modo de estudio no tiene límite de tiempo. Tras responder, puedes ver el resultado y las opciones correctas. Puedes volver a una pregunta y repetir el tema.

Simulacro

Un simulacro dura hasta 60 minutos e incluye hasta 50 preguntas de la colección elegida. Las soluciones y los resultados aparecen al terminar.

Ejemplos de preguntas y respuestas

Estos ejemplos pertenecen a la colección. Elige Estudio para practicar en orden o Simulacro para comprobar tus conocimientos.

You are going to work on equipment that has been isolated, but which was previously pressurised or full of fluid. Which TWO of these precautions should be followed? Select the TWO best answers.

Varias respuestas correctas

  • Use any drain and vent valves fitted, checking that they are clear.✓ Respuesta correcta
  • Loosen the bolts at off flanges but leaving the nuts on. Then just break the joint at the flange.✓ Respuesta correcta
  • Give the isolating valves extra force with a wheel key.
  • Fully open a flange at the top of the equipment first.
How can safe isolation be maintained when more than one person is working on the same system, for instance in dry-dock? Select the ONE best answer.

Una respuesta correcta

  • Each person should apply their own locks at the points of isolation.✓ Respuesta correcta
  • There should be a verbal agreement to check with each other before restoring the equipment to service.
  • One person should agree to take charge of the situation.
  • They should leave the locking arrangements to the Master or Chief Engineer.
If the equipment you are working on can move downwards under gravity, what should you do to keep safe? Select the ONE best answer.

Una respuesta correcta

  • Make sure that it is securely locked into position or properly supported.✓ Respuesta correcta
  • Always work from above it.
  • Make sure that no-one can walk underneath it.
  • Only do the job when in port, so that the ship is not rolling.
If the person that applied the lock and tag out to a system is not available, what should be done when work is completed? Select the ONE best answer.

Una respuesta correcta

  • Follow the on board procedure for such an event.✓ Respuesta correcta
  • The Chief Engineer or Chief Mate will remove them.
  • Anyone who has been involved in the work can remove them.
  • Leave them in place till the original person is available.
You have been working on electrical, pneumatic or hydraulic equipment. What should be done about the controls for the equipment before re-energising it? Select the ONE correct answer.

Una respuesta correcta

  • The controls should be put into a safe position, usually the ‘off’ position.✓ Respuesta correcta
  • The controls should be checked to make sure they are in the same position they were when the work started.
  • Nothing needs to be checked, the equipment is not likely to start.
  • The controls should be placed to the ‘on’ position.

Antes de empezar

¿Tengo que registrarme para empezar?

Puedes acceder como invitado durante 23 minutos. Regístrate gratis para seguir, guardar el progreso y revisar tus errores.

¿En qué idioma están las preguntas?

Las preguntas y las opciones conservan su idioma original. Puedes cambiar el idioma de la interfaz por separado.

¿Puedo usar mi resultado como documento oficial?

No. Es una práctica independiente. El resultado no sustituye un examen, certificado o prueba de una entidad autorizada.