Alle internationalen Übungstests auf IG MARITIME stehen Seeleuten kostenlos zur Verfügung. Registrieren Sie sich einmal, um Ihren Fortschritt zu speichern und ohne Einschränkungen zu üben.

EO1-Use Hand and Power Tools for Fabrication and Repair

Diesen Bereich durchsuchen

Wählen Sie einen Fragensatz und starten Sie den Lernmodus oder eine Probeprüfung.

Über diesen Fragensatz

Im Bereich Видеотел finden Sie Fragen zur eigenständigen Vorbereitung. Wählen Sie einen Fragensatz für den Lernmodus oder eine Probeprüfung.

„Видеотел — Engine Category — EO1-Use Hand and Power Tools for Fabrication and Repair“ enthält 172 Fragen in 1 Sammlung.

Lernmodus

Der Lernmodus hat kein Zeitlimit. Nach jeder Antwort sehen Sie die Auswertung und die richtigen Optionen. Sie können Fragen und Themen wiederholen.

Probeprüfung

Eine Probeprüfung dauert bis zu 60 Minuten und umfasst bis zu 50 Fragen aus dem gewählten Satz. Die Lösungen und Ergebnisse erscheinen nach Abschluss.

Beispielfragen und Antworten

Diese Beispiele stammen aus dem Fragensatz. Wählen Sie den Lernmodus für die schrittweise Bearbeitung oder eine Probeprüfung zum Selbsttest.

What kind of tool is shown bottom left ? What is its use ?Abbildung zur Frage

Eine richtige Antwort

  • 1) Mason's chisel / To break up cement boxes.
  • 2) Blacksmith's chisel / To cut steel bars and rods.
  • 3) Hot chisel / To cut bolts and nuts.
  • 4) Cold chisel / A general purpose cutting and splitting tool.✓ Richtige Antwort
A scriber should not be used for marking out?Abbildung zur Frage

Eine richtige Antwort

  • 1) When material is copper.
  • 2) When material is to be bent.✓ Richtige Antwort
  • 3) When material is to be hot worked.
  • 4) When material is plastic.
Perspex is an example of a thermoplastic, How is this best heated prior to bending?Das Originalbild ist nicht verfügbar.

Eine richtige Antwort

  • 1) Heat in an oven.
  • 2) Heat in boiling water.✓ Richtige Antwort
  • 3) Flame heat.
  • 4) Hot air stream.
What is the function of this hydraulic stressing tool when fastening and unfastening bolts/nuts on an engine ?Abbildung zur Frage

Eine richtige Antwort

  • 1) To fasten or unfasten the nut.
  • 2) To press the part to be fastened together or down so that the nut can be tightened by hand.
  • 3) To apply pressure on cylinder head or bearing so that the bolts/nuts can be tightened by hand.
  • 4) To elongate the bolts at required stress value so that the nuts can be tightened to the position to ensure correct pre-tensioning.✓ Richtige Antwort
A method of joining two plastics together is by solvent welding. What is this process?Das Originalbild ist nicht verfügbar.

Eine richtige Antwort

  • 1) Application of a thin film of adhesive to joining surfaces.
  • 2) Adhesive is applied and dissolves the plastic material being joined.✓ Richtige Antwort
  • 3) A heating tool is applied with pressure to required join.
  • 4) A high frequency current is applied to clamps at the join.

Vor dem Start

Muss ich mich vor dem Start registrieren?

Der Gastzugang dauert 23 Minuten. Registrieren Sie sich kostenlos, um weiterzulernen, den Fortschritt zu speichern und Fehler nachzuarbeiten.

In welcher Sprache sind die Fragen?

Fragen und Antwortoptionen bleiben in ihrer Originalsprache. Die Sprache der Oberfläche können Sie unabhängig davon ändern.

Kann ich das Ergebnis als offizielles Dokument verwenden?

Nein. Dies ist eine selbstständige Übung. Das Ergebnis ersetzt keine Prüfung, Bescheinigung oder Wissenskontrolle einer zugelassenen Stelle.