Alle internationalen Übungstests auf IG MARITIME stehen Seeleuten kostenlos zur Verfügung. Registrieren Sie sich einmal, um Ihren Fortschritt zu speichern und ohne Einschränkungen zu üben.

CD7055. TOTS 1C-Operation, monitoring, machinery

Diesen Bereich durchsuchen

Wählen Sie einen Fragensatz und starten Sie den Lernmodus oder eine Probeprüfung.

Über diesen Fragensatz

Im Bereich Seagull CBT finden Sie Fragen zur eigenständigen Vorbereitung. Wählen Sie einen Fragensatz für den Lernmodus oder eine Probeprüfung.

„Seagull CBT — CD7055. TOTS 1C-Operation, monitoring, machinery“ enthält 76 Fragen in 1 Sammlung.

Lernmodus

Der Lernmodus hat kein Zeitlimit. Nach jeder Antwort sehen Sie die Auswertung und die richtigen Optionen. Sie können Fragen und Themen wiederholen.

Probeprüfung

Eine Probeprüfung dauert bis zu 60 Minuten und umfasst bis zu 50 Fragen aus dem gewählten Satz. Die Lösungen und Ergebnisse erscheinen nach Abschluss.

Beispielfragen und Antworten

Diese Beispiele stammen aus dem Fragensatz. Wählen Sie den Lernmodus für die schrittweise Bearbeitung oder eine Probeprüfung zum Selbsttest.

If the safety valves fitted on an air reservoir can be isolated from the reservoir, then..

Eine richtige Antwort

  • the reservoir must be fitted with a fusible plug.✓ Richtige Antwort
  • the safety valve must be fitted with a fusible plug.
  • the compressor must be fitted with a fusible plug.
  • it can be used legally without any added safety measures.
What is the most common cause of the lowering in performance of heat exchangers?

Eine richtige Antwort

  • Fouling of the heat transfer surface.✓ Richtige Antwort
  • An air lock.
  • Low water flow.
  • The division plate joint failure.
During discharge, problems with the inert gas plant result in the production of clean inert gas being reduced by 50%. What do you do?

Eine richtige Antwort

  • Advise the Chief Officer so that he can reduce the discharge rate in line with the reduction of the gas supply.✓ Richtige Antwort
  • Adjust the boiler controls to increase the fuel and reduce the air in an attempt to reduce the oxygen content of the gas.
  • Allow the discharge to continue as the oxygen content in the tanks may not rise significantly during the remaining discharge period.
  • Shut down the discharge until the inert gas system problem is resolved.
In plate type coolers you would normally expect the plates to be made of..

Eine richtige Antwort

  • titanium.✓ Richtige Antwort
  • silver.
  • stainless steel.
  • nickel brass.
The cause of an abnormally high condenser pressure within a refrigeration system would be..

Eine richtige Antwort

  • incondensable gases in the refrigerant.✓ Richtige Antwort
  • a low cooling water flow through the condenser.
  • a defective thermal expansion valve.
  • an above normal level of refrigerant in the condenser.

Vor dem Start

Muss ich mich vor dem Start registrieren?

Der Gastzugang dauert 23 Minuten. Registrieren Sie sich kostenlos, um weiterzulernen, den Fortschritt zu speichern und Fehler nachzuarbeiten.

In welcher Sprache sind die Fragen?

Fragen und Antwortoptionen bleiben in ihrer Originalsprache. Die Sprache der Oberfläche können Sie unabhängig davon ändern.

Kann ich das Ergebnis als offizielles Dokument verwenden?

Nein. Dies ist eine selbstständige Übung. Das Ergebnis ersetzt keine Prüfung, Bescheinigung oder Wissenskontrolle einer zugelassenen Stelle.