Alle internationalen Übungstests auf IG MARITIME stehen Seeleuten kostenlos zur Verfügung. Registrieren Sie sich einmal, um Ihren Fortschritt zu speichern und ohne Einschränkungen zu üben.

CD0420. Lockout Tagout

Diesen Bereich durchsuchen

Wählen Sie einen Fragensatz und starten Sie den Lernmodus oder eine Probeprüfung.

Über diesen Fragensatz

Im Bereich Seagull CBT finden Sie Fragen zur eigenständigen Vorbereitung. Wählen Sie einen Fragensatz für den Lernmodus oder eine Probeprüfung.

„Seagull CBT — CD0420. Lockout Tagout“ enthält 10 Fragen in 1 Sammlung.

Lernmodus

Der Lernmodus hat kein Zeitlimit. Nach jeder Antwort sehen Sie die Auswertung und die richtigen Optionen. Sie können Fragen und Themen wiederholen.

Probeprüfung

Eine Probeprüfung dauert bis zu 60 Minuten und umfasst bis zu 50 Fragen aus dem gewählten Satz. Die Lösungen und Ergebnisse erscheinen nach Abschluss.

Beispielfragen und Antworten

Diese Beispiele stammen aus dem Fragensatz. Wählen Sie den Lernmodus für die schrittweise Bearbeitung oder eine Probeprüfung zum Selbsttest.

You are going to work on equipment that has been isolated, but which was previously pressurised or full of fluid. Which TWO of these precautions should be followed? Select the TWO best answers.

Mehrere richtige Antworten

  • Use any drain and vent valves fitted, checking that they are clear.✓ Richtige Antwort
  • Loosen the bolts at off flanges but leaving the nuts on. Then just break the joint at the flange.✓ Richtige Antwort
  • Give the isolating valves extra force with a wheel key.
  • Fully open a flange at the top of the equipment first.
How can safe isolation be maintained when more than one person is working on the same system, for instance in dry-dock? Select the ONE best answer.

Eine richtige Antwort

  • Each person should apply their own locks at the points of isolation.✓ Richtige Antwort
  • There should be a verbal agreement to check with each other before restoring the equipment to service.
  • One person should agree to take charge of the situation.
  • They should leave the locking arrangements to the Master or Chief Engineer.
If the equipment you are working on can move downwards under gravity, what should you do to keep safe? Select the ONE best answer.

Eine richtige Antwort

  • Make sure that it is securely locked into position or properly supported.✓ Richtige Antwort
  • Always work from above it.
  • Make sure that no-one can walk underneath it.
  • Only do the job when in port, so that the ship is not rolling.
If the person that applied the lock and tag out to a system is not available, what should be done when work is completed? Select the ONE best answer.

Eine richtige Antwort

  • Follow the on board procedure for such an event.✓ Richtige Antwort
  • The Chief Engineer or Chief Mate will remove them.
  • Anyone who has been involved in the work can remove them.
  • Leave them in place till the original person is available.
You have been working on electrical, pneumatic or hydraulic equipment. What should be done about the controls for the equipment before re-energising it? Select the ONE correct answer.

Eine richtige Antwort

  • The controls should be put into a safe position, usually the ‘off’ position.✓ Richtige Antwort
  • The controls should be checked to make sure they are in the same position they were when the work started.
  • Nothing needs to be checked, the equipment is not likely to start.
  • The controls should be placed to the ‘on’ position.

Vor dem Start

Muss ich mich vor dem Start registrieren?

Der Gastzugang dauert 23 Minuten. Registrieren Sie sich kostenlos, um weiterzulernen, den Fortschritt zu speichern und Fehler nachzuarbeiten.

In welcher Sprache sind die Fragen?

Fragen und Antwortoptionen bleiben in ihrer Originalsprache. Die Sprache der Oberfläche können Sie unabhängig davon ändern.

Kann ich das Ergebnis als offizielles Dokument verwenden?

Nein. Dies ist eine selbstständige Übung. Das Ergebnis ersetzt keine Prüfung, Bescheinigung oder Wissenskontrolle einer zugelassenen Stelle.